Drywall Repair Isn’t Indestructible

Drywall is a durable material, but it isn’t indestructible. A door knob, a vacuum cleaner, or a child flinging a toy can all dent it.


Small holes can be repaired easily with a drywall patch kit. Just be sure to buy a roll of paper tape and a gallon tub of joint compound. Contact Las Vegas Drywall Repair for professional help.

Water damage to drywall is one of the most common issues homeowners encounter. Left unchecked, this type of damage can lead to mold and mildew and may even cause structural problems in walls and ceilings. Water damage is caused by many different things, from flooding and hurricanes to burst pipes and sink overflows. Homeowners should regularly inspect their homes for signs of moisture, such as stains on walls or ceilings, or a musty smell. If you spot any of these issues, call a professional right away to help fix the problem before it becomes serious.

The first step in repairing water damaged drywall is to locate and fix the source of the problem. Once you’ve done that, the next step is to fully dry the affected area. To do this, you can drain standing water from the area and use an area fan to help circulate air. You can also use a dehumidifier to further reduce humidity in the room. If possible, open the doors and windows to further assist with drying. On average, it takes three days for wet drywall to completely dry.

Once the drywall is dry, you can patch the hole. If the drywall is severely damaged, you might need to replace it entirely. However, in less severe cases, you can patch the drywall by cutting out the damaged area and inserting a new piece of drywall. The replacement drywall should be about 2 inches longer and wider than the original drywall, so you’ll need to cut a straight line using a pencil or a ruler. You should then remove any insulation (fiberglass, mineral wool, cellulose or wood fiberboard) that’s inside the wall.

If there’s any black mold present, it should be professionally remediated by a professional. Mold in drywall is not only unsightly, but it can also be toxic and harmful to your health. If there’s a lot of black mold in the drywall, it may be a sign of a more severe issue and should be addressed immediately by professionals.


Whether from nails or screws that are used to hang something on the wall, or a doorknob-sized hole caused by a slammed door, drywall is not indestructible. Holes and dents are often a sign that the drywall is past its prime and needs to be replaced. Luckily, holes are one of the easier home repair projects to tackle if you have the right tools and follow a few key steps.

Drywall patch kits are designed to take the guesswork out of fixing a hole in drywall. The first step is to use the patch kit to place a sheet of mesh over the hole, making sure that it is completely covered with no jagged edges, then a layer of drywall joint compound (aka mud) is spread over the top of the patch and smoothed out around the edges to blend with the rest of the wall. This is then left to dry overnight. If you or a painting service plan to repaint the area, it’s important that the mud is lightly sanded down to create a flush surface.

When the sheets of drywall meet at corners, an L-shaped metal strip called corner bead is nailed over the joints and concealed with another layer of joint compound. Corner bead is not indestructible, however, and can become dented from a slammed door, flying toys, or furniture that’s being moved. It’s important to repair these dents quickly and thoroughly before they can cause further damage to the drywall or lead to a leak.

While you’re working on repairing holes or dents, it’s important to use a stud finder to locate and mark the nearest studs on either side of the damaged area before cutting into the drywall. This ensures that you don’t accidentally cut into electrical cords or plumbing lines.

While you’re doing your repairs, be sure to keep a close eye on children and pets in case they run into the work area. This can prevent accidental injuries that could result in even more expensive home repairs down the road. It’s also a good idea to regularly inspect the house for pests like termites and carpenter ants, which can cause significant damage in a short amount of time.


If you have a few small cracks or indentations in your drywall, they can easily be repaired with spackle and a smoothing tool. Then, with a little interior painting over the area, the wall will look as good as new. Larger holes or cracks, however, may require a more extensive patching job.

Cracks in drywall can be caused by normal settling, moisture damage or a number of other issues. They often appear along a seam in-between drywall panels or near doors and windows. Cracks are most commonly found in older homes, but can also be seen in newly constructed houses. Regardless of the cause, they should be repaired as soon as possible to prevent further damage and potential structural problems.

When a crack appears in your drywall, the first step is to clean the surface thoroughly with a vacuum cleaner or brush. This will help the drywall repair adhere properly. Next, apply a liberal layer of drywall compound or spackle to the crack. Once the compound has set, sand it smooth using coarse grit sandpaper and then use fine sandpaper to remove any remaining traces of the repair. Finally, apply a coat of primer to the repaired area and allow it to dry before applying your choice of paint.

Normal settling: Cracks in drywall that occur naturally and are not the result of a structural problem are usually referred to as hairline cracks. These are not uncommon and are a result of the house shifting and expanding as the foundation settles. These cracks are not a serious issue, but should be monitored over time.

Moisture damage: If you notice a pattern of drywall cracks that are accompanied by brown or yellow tinted stains, it’s likely due to water damage. Leaky windows and roofs can cause moisture to build up in the walls, which causes the drywall to soften and eventually crack. If left untreated, this can lead to mold and other serious issues.

Other causes of drywall cracks include stress, thermal changes and hanging heavy items on the wall. To reduce the likelihood of cracks, make sure to hang light items evenly across the wall and to avoid placing a lot of stress on one section of the wall. It’s also important to maintain a consistent temperature throughout the house and avoid drastic fluctuations.


Mold is a major problem that can occur when drywall becomes exposed to moisture. It can also be caused by plumbing issues or improper insulation that allows moisture to gather inside a wall. When this happens, it’s essential to take steps to remove the mold and identify the cause of the problem in order to prevent it from occurring again. Mold in a home or apartment building can affect residents’ health, especially those with allergies or asthma. It can also weaken the structure of a wall and lead to further problems, so it’s important to address the issue as soon as possible.

If you notice a mushy or bubbling area of your drywall, it’s likely because of mold. Mold grows wherever there’s something organic (food for the fungus), oxygen, and moisture, which drywall absorbs very easily. Mold is most often found in areas of your walls with water damage. It can appear as dark spots or patches on the walls, or it may look like a damp spot that’s not quite dry yet.

Drywall with mold is usually a sign that there’s a more serious problem, such as water leaks or rotted wood in the studs behind it. It’s important to contact a professional for a drywall repair in this case, as moldy drywall will need to be replaced so that the mold doesn’t spread and create a bigger problem.

Mold in a house or apartment can affect residents’ health, including those who don’t have any allergies or asthma. It can weaken the structural integrity of a building and contribute to further problems, such as leaks or cracks in other parts of the house. It can also make it difficult to breathe, causing respiratory infections and lung conditions.

Depending on the severity of the mold, it may be necessary to replace the entire sheet of drywall in the affected room. However, if the mold isn’t too bad and you catch it quickly, it may be possible to clean the moldy drywall and paint it again without replacing it. To do this, you’ll need to apply a second coat of joint compound and sand it to smooth and feather the edges before painting.